[Code of Federal Regulations] [Title 49, Volume 2] [Revised as of October 1, 2005] From the U.S. Government Printing Office via GPO Access [CITE: 49CFR173.35] [Page 460-462] TITLE 49--TRANSPORTATION CHAPTER I--PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PART 173_SHIPPERS_GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS --Table of Contents Subpart B_Preparation of Hazardous Materials for Transportation Sec. 173.35 Hazardous materials in IBCs. (a) No person may offer or accept a hazardous material for transportation in an IBC except as authorized by this subchapter. Each IBC used for the transportation of hazardous materials must conform to the requirements of its specification and regulations for the transportation of the particular commodity. A specification IBC, for which the prescribed periodic retest or inspection under subpart D of part 180 of this subchapter is past due, may not be filled and offered for transportation until the retest or inspection have been [[Page 461]] successfully completed. This requirement does not apply to any IBC filled prior to the retest or inspection due date. (b) Initial use and reuse of IBCs. (Also see Sec. 180.352 of this subchapter.) An IBC other than a multiwall paper IBC (13M1 and 13M2) may be reused. If an inner liner is required, the inner liner must be replaced before each reuse. Before an IBC is filled and offered for transportation, the IBC and its service equipment must be given an external visual inspection, by the person filling the IBC, to ensure that: (1) The IBC is free from corrosion, contamination, cracks, cuts, or other damage which would render it unable to pass the prescribed design type test to which it is certified and marked; and (2) The IBC is marked in accordance with requirements in Sec. 178.703 of this subchapter. Additional marking allowed for each design type may be present. Required markings that are missing, damaged or difficult to read must be restored or returned to original condition. (c) A metal IBC, or a part thereof, subject to thinning by mechanical abrasion or corrosion due to the lading, must be protected by providing a suitable increase in thickness of material, a lining or some other suitable method of protection. Increased thickness for corrosion or abrasion protection must be added to the wall thickness specified in Sec. 178.705(c)(1)(iv) of this subchapter. (d) Notwithstanding requirements in Sec. 173.24b of this subpart, when filling an IBC with liquids, sufficient ullage must be left to ensure that, at the mean bulk temperature of 50 [deg]C (122 [deg]F), the IBC is not filled to more than 98 percent of its water capacity. (e) Where two or more closure systems are fitted in series, the system nearest to the hazardous material being carried must be closed first. (f) During transportation-- (1) No hazardous material may remain on the outside of the IBC; and (2) Each IBC must be securely fastened to or contained within the transport unit. (g) Each IBC used for transportation of solids which may become liquid at temperatures likely to be encountered during transportation must also be capable of containing the substance in the liquid state. (h) Liquid hazardous materials may only be offered for transportation in a metal, rigid plastic, or composite IBC that is appropriately resistant to an increase of internal pressure likely to develop during transportation. (1) A rigid plastic or composite IBC may only be filled with a liquid having a vapor pressure less than or equal to the greater of the following two values: the first value is determined from any of the methods in paragraphs (h)(1) (i), (ii) or (iii) of this section. The second value is determined by the method in paragraph (h)(1)(iv) of this section. (i) The gauge pressure (pressure in the IBC above ambient atmospheric pressure) measured in the IBC at 55 [deg]C (131 [deg]F). This gauge pressure must not exceed two-thirds of the marked test pressure and must be determined after the IBC was filled and closed at 15 [deg]C (60 [deg]F) to less than or equal to 98 percent of its capacity. (ii) The absolute pressure (vapor pressure of the hazardous material plus atmospheric pressure) in the IBC at 50 [deg]C (122 [deg]F). This absolute pressure must not exceed four-sevenths of the sum of the marked test pressure and 100 kPa (14.5 psia). (iii) The absolute pressure (vapor pressure of the hazardous material plus atmospheric pressure) in the IBC at 55 [deg]C (131 [deg]F). This absolute pressure must not exceed two-thirds of the sum of the marked test pressure and 100 kPa (14.5 psia). (iv) Twice the static pressure of the substance, measured at the bottom of the IBC. This value must not be less than twice the static pressure of water. (2) Gauge pressure (pressure in the IBC above ambient atmospheric pressure) in metal IBC must not exceed 110 kPa (16 psig) at 50 [deg]C (122 [deg]F) or 130 kPa (18.9 psig) at 55 [deg]C (131 [deg]F). (i) The requirements in this section do not apply to DOT-56 or -57 portable tanks. (j) No IBC may be filled with a Packing Group I liquid. Rigid plastic, composite, flexible, wooden or fiberboard IBC used to transport Packing Group I solid materials may not exceed 1.5 cubic meters (53 cubic feet) capacity. For Packing Group I solids, a metal [[Page 462]] IBC may not exceed 3 cubic meters (106 cubic feet) capacity. (k) When an IBC is used for the transportation of liquids with a flash point of 60.5 [deg]C (141 [deg]F) (closed cup) or lower, or powders with the potential for dust explosion, measures must be taken during product loading and unloading to prevent a dangerous electrostatic discharge. (l) IBC filling limits. (1) Except as provided in this section, an IBC may not be filled with a hazardous material in excess of the maximum gross mass marked on that container. (2) An IBC which is tested and marked for Packing Group II liquid materials may be filled with a Packing Group III liquid material to a gross mass not exceeding 1.5 times the maximum gross mass marked on that container, if all the performance criteria can still be met at the higher gross mass. (3) An IBC which is tested and marked for liquid hazardous materials may be filled with a solid hazardous material to a gross mass not exceeding the maximum gross mass marked on that container. In addition, an IBC intended for the transport of liquids which is tested and marked for Packing Group II liquid materials may be filled with a Packing Group III solid hazardous material to a gross mass not exceeding the marked maximum gross mass multiplied by 1.5 if all the performance criteria can still be met at the higher gross mass. (4) An IBC which is tested and marked for Packing Group I solid materials may be filled with a Packing Group II solid material to a gross mass not exceeding the maximum gross mass marked on that container, multiplied by 1.5, if all the performance criteria can be met at the higher gross mass; or a Packing Group III solid material to a gross mass not exceeding the maximum gross mass marked on the IBC, multiplied by 2.25, if all the performance criteria can be met at the higher gross mass. An IBC which is tested and marked for Packing Group II solid materials may be filled with a Packing Group III solid material to a gross mass not exceeding the maximum gross mass marked on the IBC, multiplied by 1.5. [Amdt. 173-238, 59 FR 38064, July 26, 1994, as amended by Amdt. 173-243, 60 FR 40038, Aug. 4, 1995; 64 FR 10777, Mar. 5, 1999; 66 FR 45380, 45381, Aug. 28, 2001; 68 FR 48569, Aug. 14, 2003]