[Code of Federal Regulations] [Title 49, Volume 2] [Revised as of October 1, 2005] From the U.S. Government Printing Office via GPO Access [CITE: 49CFR173.62] [Page 478-492] TITLE 49--TRANSPORTATION CHAPTER I--PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PART 173_SHIPPERS_GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS --Table of Contents Subpart C_Definitions, Classification and Packaging for Class 1 Sec. 173.62 Specific packaging requirements for explosives. (a) Except as provided in Sec. 173.7 of this subchapter, when the Sec. 172.101 Table specifies that an explosive must be packaged in accordance with this section, only packagings which conform to the provisions of paragraphs (b) and (c) of this section or Sec. 173.7(e) of this subchapter and the applicable requirements in Sec. Sec. 173.60 and 173.61 may be used unless otherwise approved by the Associate Administrator. (b) Explosives Table. The Explosives Table specifies the Packing Instructions assigned to each explosive. Explosives are identified in the first column in numerical sequence by their identification number (ID ), which is listed in column 4 of the Sec. 172.101 table, of this subchapter. The second column of the Explosives Table specifies the Packing Instruction (PI) which must be used for packaging the explosive. The Explosives Packing Method Table in paragraph (c) of this section defines the methods of packaging. The Packing Instructions are identified using a 3 digit designation. The Packing Instruction prefixed by the letters ``US'' is particular to the United States and not found in applicable international regulations. Explosives Table ------------------------------------------------------------------------ ID PI ------------------------------------------------------------------------ UN0004.............................. 112 UN0005.............................. 130 UN0006.............................. 130 UN0007.............................. 130 UN0009.............................. 130 UN0010.............................. 130 UN0012.............................. 130 UN0014.............................. 130 [[Page 479]] UN0015.............................. 130 UN0016.............................. 130 UN0018.............................. 130 UN0019.............................. 130 UN0020.............................. 101 UN0021.............................. 101 UN0027.............................. 113 UN0028.............................. 113 UN0029.............................. 131 UN0030.............................. 131 UN0033.............................. 130 UN0034.............................. 130 UN0035.............................. 130 UN0037.............................. 130 UN0038.............................. 130 UN0039.............................. 130 UN0042.............................. 132 UN0043.............................. 133 UN0044.............................. 133 UN0048.............................. 130 UN0049.............................. 135 UN0050.............................. 135 UN0054.............................. 135 UN0055.............................. 136 UN0056.............................. 130 UN0059.............................. 137 UN0060.............................. 132 UN0065.............................. 139 UN0066.............................. 140 UN0070.............................. 134 UN0072.............................. 112(a) UN0073.............................. 133 UN0074.............................. 110(a) or 110(b) UN0075.............................. 115 UN0076.............................. 112 UN0077.............................. 114(a) or 114(b) UN0078.............................. 112 UN0079.............................. 112(b) or 112(c) UN0081.............................. 116 UN0082.............................. 116 or 117 UN0083.............................. 116 UN0084.............................. 116 UN0092.............................. 135 UN0093.............................. 135 UN0094.............................. 113 UN0099.............................. 134 UN0101.............................. 140 UN0102.............................. 139 UN0103.............................. 140 UN0104.............................. 139 UN0105.............................. 140 UN0106.............................. 141 UN0107.............................. 141 UN0110.............................. 141 UN0113.............................. 110(a) or 110(b) UN0114.............................. 110(a) or 110(b) UN0118.............................. 112 UN0121.............................. 142 UN0124.............................. US1 UN0129.............................. 110(a) or 110(b) UN0130.............................. 110(a) or 110(b) UN0131.............................. 142 UN0132.............................. 114(b) UN0133.............................. 112(a) UN0135.............................. 110(a) or 110(b) UN0136.............................. 130 UN0137.............................. 130 UN0138.............................. 130 UN0143.............................. 115 UN0144.............................. 115 UN0146.............................. 112 UN0147.............................. 112(b) UN0150.............................. 112(a) or 112(b) UN0151.............................. 112 UN0153.............................. 112(b) or 112(c) UN0154.............................. 112 UN0155.............................. 112(b) or 112(c) UN0159.............................. 111 UN0160.............................. 114(b) UN0161.............................. 114(b) UN0167.............................. 130 UN0168.............................. 130 UN0169.............................. 130 UN0171.............................. 130 UN0173.............................. 134 UN0174.............................. 134 UN0180.............................. 130 UN0181.............................. 130 UN0182.............................. 130 UN0183.............................. 130 UN0186.............................. 130 UN0190.............................. 101 UN0191.............................. 135 UN0192.............................. 135 UN0193.............................. 135 UN0194.............................. 135 UN0195.............................. 135 UN0196.............................. 135 UN0197.............................. 135 UN0204.............................. 134 UN0207.............................. 112(b) or 112(c) UN0208.............................. 112(b) or 112(c) UN0209.............................. 112 UN0212.............................. 133 UN0213.............................. 112(b) or 112(c) UN0214.............................. 112 UN0215.............................. 112 UN0216.............................. 112(b) or 112(c) UN0217.............................. 112(b) or 112(c) UN0218.............................. 112(b) or 112(c) UN0219.............................. 112 UN0220.............................. 112 UN0221.............................. 130 UN0222.............................. 112(b) or 112(c) UN0224.............................. 110(a) or 110(b) UN0225.............................. 133 UN0226.............................. 112(a) UN0234.............................. 114(a) or 114(b) UN0235.............................. 114(a) or 114(b) UN0236.............................. 114(a) or 114(b) UN0237.............................. 138 UN0238.............................. 130 UN0240.............................. 130 UN0241.............................. 116 or 117 UN0242.............................. 130 UN0243.............................. 130 UN0244.............................. 130 UN0245.............................. 130 UN0246.............................. 130 UN0247.............................. 101 UN0248.............................. 144 UN0249.............................. 144 UN0250.............................. 101 UN0254.............................. 130 UN0255.............................. 131 UN0257.............................. 141 UN0266.............................. 112 UN0267.............................. 131 UN0268.............................. 133 UN0271.............................. 143 UN0272.............................. 143 UN0275.............................. 134 UN0276.............................. 134 UN0277.............................. 134 [[Page 480]] UN0278.............................. 134 UN0279.............................. 130 UN0280.............................. 130 UN0281.............................. 130 UN0282.............................. 112 UN0283.............................. 132 UN0284.............................. 141 UN0285.............................. 141 UN0286.............................. 130 UN0287.............................. 130 UN0288.............................. 138 UN0289.............................. 139 UN0290.............................. 139 UN0291.............................. 130 UN0292.............................. 141 UN0293.............................. 141 UN0294.............................. 130 UN0295.............................. 130 UN0296.............................. 134 UN0297.............................. 130 UN0299.............................. 130 UN0300.............................. 130 UN0301.............................. 130 UN0303.............................. 130 UN0305.............................. 113 UN0306.............................. 133 UN0312.............................. 135 UN0313.............................. 135 UN0314.............................. 142 UN0315.............................. 142 UN0316.............................. 141 UN0317.............................. 141 UN0318.............................. 141 UN0319.............................. 133 UN0320.............................. 133 UN0321.............................. 130 UN0322.............................. 101 UN0323.............................. 134 UN0324.............................. 130 UN0325.............................. 142 UN0326.............................. 130 UN0327.............................. 130 UN0328.............................. 130 UN0329.............................. 130 UN0330.............................. 130 UN0331.............................. 116 or 117 UN0332.............................. 116 or 117 UN0333.............................. 135 UN0334.............................. 135 UN0335.............................. 135 UN0336.............................. 135 UN0337.............................. 135 UN0338.............................. 130 UN0339.............................. 130 UN0340.............................. 112(a) or 112(b) UN0341.............................. 112(b) UN0342.............................. 114(a) UN0343.............................. 111 UN0344.............................. 130 UN0345.............................. 130 UN0346.............................. 130 UN0347.............................. 130 UN0348.............................. 130 UN0349.............................. 101 UN0350.............................. 101 UN0351.............................. 101 UN0352.............................. 101 UN0353.............................. 101 UN0354.............................. 101 UN0355.............................. 101 UN0356.............................. 101 UN0357.............................. 101 UN0358.............................. 101 UN0359.............................. 101 UN0360.............................. 131 UN0361.............................. 131 UN0362.............................. 130 UN0363.............................. 130 UN0364.............................. 133 UN0365.............................. 133 UN0366.............................. 133 UN0367.............................. 141 UN0368.............................. 141 UN0369.............................. 130 UN0370.............................. 130 UN0371.............................. 130 UN0372.............................. 141 UN0373.............................. 135 UN0374.............................. 134 UN0375.............................. 134 UN0376.............................. 133 UN0377.............................. 133 UN0378.............................. 133 UN0379.............................. 136 UN0380.............................. 101 UN0381.............................. 134 UN0382.............................. 101 UN0383.............................. 101 UN0384.............................. 101 UN0385.............................. 112(b) or 112(c) UN0386.............................. 112(b) or 112(c) UN0387.............................. 112(b) or 112(c) UN0388.............................. 112(b) or 112(c) UN0389.............................. 112(b) or 112(c) UN0390.............................. 112(b) or 112(c) UN0391.............................. 112(a) UN0392.............................. 112(b) or 112(c) UN0393.............................. 112(b) UN0394.............................. 112(a) UN0395.............................. 101 UN0396.............................. 101 UN0397.............................. 101 UN0398.............................. 101 UN0399.............................. 101 UN0400.............................. 101 UN0401.............................. 112 UN0402.............................. 112(b) or 112(c) UN0403.............................. 135 UN0404.............................. 135 UN0405.............................. 135 UN0406.............................. 114(b) UN0407.............................. 114(b) UN0408.............................. 141 UN0409.............................. 141 UN0410.............................. 141 UN0411.............................. 112(b) or 112(c) UN0412.............................. 130 UN0413.............................. 130 UN0414.............................. 130 UN0415.............................. 143 UN0417.............................. 130 UN0418.............................. 135 UN0419.............................. 135 UN0420.............................. 135 UN0421.............................. 135 UN0424.............................. 130 UN0425.............................. 130 UN0426.............................. 130 UN0427.............................. 130 UN0428.............................. 135 UN0429.............................. 135 UN0430.............................. 135 UN0431.............................. 135 UN0432.............................. 135 [[Page 481]] UN0433.............................. 111 UN0434.............................. 130 UN0435.............................. 130 UN0436.............................. 130 UN0437.............................. 130 UN0438.............................. 130 UN0439.............................. 137 UN0440.............................. 137 UN0441.............................. 137 UN0442.............................. 137 UN0443.............................. 137 UN0444.............................. 137 UN0445.............................. 137 UN0446.............................. 136 UN0447.............................. 136 UN0448.............................. 114(b) UN0449.............................. 101 UN0450.............................. 101 UN0451.............................. 130 UN0452.............................. 141 UN0453.............................. 130 UN0454.............................. 142 UN0455.............................. 131 UN0456.............................. 131 UN0457.............................. 130 UN0458.............................. 130 UN0459.............................. 130 UN0460.............................. 130 UN0461.............................. 101 UN0462.............................. 101 UN0463.............................. 101 UN0464.............................. 101 UN0465.............................. 101 UN0466.............................. 101 UN0467.............................. 101 UN0468.............................. 101 UN0469.............................. 101 UN0470.............................. 101 UN0471.............................. 101 UN0472.............................. 101 UN0473.............................. 101 UN0474.............................. 101 UN0475.............................. 101 UN0476.............................. 101 UN0477.............................. 101 UN0478.............................. 101 UN0479.............................. 101 UN0480.............................. 101 UN0481.............................. 101 UN0482.............................. 101 UN0483.............................. 112(b) or 112(c) UN0484.............................. 112(b) or 112(c) UN0486.............................. 101 UN0487.............................. 135 UN0488.............................. 130 UN0489.............................. 112(b) or 112(c) UN0490.............................. 112(b) or 112(c) UN0491.............................. 143 UN0492.............................. 135 UN0493.............................. 135 UN0494.............................. US1 UN0495.............................. 115 UN0496.............................. 112(b) or 112(c) UN0497.............................. 115 UN0498.............................. 114(b) UN0499.............................. 114(b) UN0500.............................. 131 UN0502.............................. 130 UN0503.............................. 135 UN0504.............................. 112(c) NA0124.............................. US1 NA0276.............................. 134 NA0323.............................. 134 NA0331.............................. 116 or 117 NA0337.............................. 135 NA0349.............................. 133 NA0494.............................. US1 ------------------------------------------------------------------------ (c) Explosives must be packaged in accordance with the following table: (1) The first column lists, in alphanumeric sequence, the packing methods prescribed for explosives in the Explosives Table of paragraph (b) of this section. (2) The second column specifies the inner packagings that are required. If inner packagings are not required, a notation of ``Not necessary'' appears in the column. The term ``Not necessary'' means that a suitable inner packaging may be used but is not required. (3) The third column specifies the intermediate packagings that are required. If intermediate packagings are not required, a notation of ``Not necessary'' appears in the column. The term ``Not necessary'' means that a suitable intermediate packaging may be used but is not required. (4) The fourth column specifies the outer packagings which are required. If inner packagings and/or intermediate packagings are specified in the second and third columns, then the packaging specified in the fourth column must be used as the outer packaging of a combination packaging; otherwise it may be used as a single packaging. (5) Packing Instruction 101 may be used for any explosive substance or article if an equivalent level of safety is shown to be maintained subject to the approval of the Associate Administrator. [[Page 482]] Table of Packing Methods ---------------------------------------------------------------------------------------------------------------- Packing instruction Inner packagings Intermediate packagings Outer packagings ---------------------------------------------------------------------------------------------------------------- 101.............................. This Packing Instruction may be used as an alternative to a specifically assigned packing method with the approval of the Associate Administrator prior to transportation. When this packing instruction is used, the following must be marked on the shipping documents: ``Packaging approved by the competent authority of the United States of America (USA)''. PARTICULAR PACKING REQUIREMENTS OR EXCEPTIONS: 1. Samples of new or existing explosive substances or articles may be transported as directed by the Associate Administrator for purposes including: testing, classification, research and development, quality control, or as a commercial sample. Explosive samples which are wetted or desensitized must be limited to 25 kg. Explosive samples which are not wetted or desensitized must be limited to 10 kg in small packages as specified by the Associate Administrator for Hazardous Materials Safety 110(a)........................... Bags..................... Bags.................... Drums. PARTICULAR PACKING REQUIREMENTS plastics............... plastics.............. steel, removable head OR EXCEPTIONS: textile, plastic coated textile, plastic coated (1A2). 1. The Intermediate packagings or lined. or lined. plastics, removable head must be filled with water rubber................... rubber.................. (1H2) saturated material such as an textile, rubberized...... textile, rubberized..... anti-freeze solution or wetted textile.................. Receptacles............. cushioning plastics................ 2. Outer packagings must be metal................... filled with water saturated material such as an anti-freeze solution or wetted cushioning. Outer packagings must be constructed and sealed to prevent evaporation of the wetting solution, except when 0224 is being carried dry 110(b)........................... Bags..................... Dividing partitions..... Boxes. PARTICULAR PACKING REQUIREMENTS rubber, conductive..... metal................. natural wood, sift- OR EXCEPTIONS plastics, conductive..... wood.................... proof wall (4C2). For UN 0074, 0113, 0114, 0129, Receptacles.............. plastics................ plywood (4D). 0130, 0135 and 0224, the metal.................... fibreboard.............. reconstituted wood (4F). following conditions must be wood..................... satisfied: rubber, conductive....... a. inner packagings must not plastics, conductive..... contain more than 50 g of explosive substance (quantity corresponding to dry substance); b. each inner packaging must be separated from other inner packagings by dividing partitions; and c. the outer packaging must not be partitioned with more than 25 compartments 111.............................. Bags..................... Not necessary........... Boxes. PARTICULAR PACKING REQUIREMENTS paper, waterproofed...... steel (4A). OR EXCEPTIONS:. plastics................. aluminium (4B). For UN 0159, inner packagings are textile, rubberized...... natural wood, ordinary not required when metal (1A2 or Sheets................... (4C1). 1B2) or plastics (1H2) drums are plastics................. natural wood, sift proof used as outer packagings. textile, rubberized...... (4C2). plywood (4D). reconstituted wood (4F). fibreboard (4G). plastics, expanded (4H1). plastics, solid (4H2). Drums steel, removable head (1A2). aluminum, removable head (1B2). plywood (1D). fibreboard (1G). plastics, removable head (1H2). 112(a) This packing instruction Bags..................... Bags.................... Boxes. applies to wetted solids. [[Page 483]] PARTICULAR PACKING REQUIREMENTS paper, multiwall, water plastics.............. steel (4A). OR EXCEPTIONS: resistant. textile, plastic coated aluminium (4B). 1. For UN Nos. 0004, 0076, 0078, plastics................. or lined. natural wood, ordinary 0154, 0219 and 0394, packagings textile.................. Receptacles............. (4C1). must be lead free textile, rubberized...... metal................... natural wood, sift proof 2. Intermediate packagings are woven plastics........... plastics................ (4C2). not required if leakproof drums Receptacles.............. plywood (4D). are used as the outer packaging metal.................... reconstituted wood (4F). 3. For UN 0072 and UN 0226, plastics................. fibreboard (4G). intermediate packagings are not plastics, expanded required (4H1). plastics, solid (4H2). Drums steel, removable head (1A2). aluminium, removable head (1B2). Plywood (1D). fibre (1G). plastics, removable head (1H2). 112(b) This packing instruction Bags..................... Bags (for UN 0150 only). Bags. applies to dry solids other than paper, Kraft............. plastics................ woven plastics sift- powders. paper, multiwall, water textile, plastic coated proof (5H2/3). PARTICULAR PACKING REQUIREMENTS resistant. or lined. plastics, film (5H4). OR EXCEPTIONS:. plastics................. textile, sift-proof 1. For UN 0004, 0076, 0078, 0154, textile.................. (5L2). 0216, 0219 and 0386, packagings textile, rubberized textile, water resistant must be lead free. plastics. (5L3). 2. For UN 0209, bags, sift-proof woven plastics........... paper, multiwall, water (5H2) are recommended for flake resistant (5M2). or prilled TNT in the dry state Boxes and a maximum net mass of 30 kg.. steel (4A). 3. For UN 0222, inner packagings aluminium (4B). are not required. natural wood, ordinary (4C1). natural wood, sift proof (4C2). plywood (4D) reconstituted wood (4F). fibreboard (4G). plastics, expanded (4H1). plastics, solid (4H2). Drums steel, removable head (1A2). aluminium, removable head (1B2). Plywood (1D). fibre (1G). plastics, removable head (1H2). 112(c) This packing instruction Bags..................... Bags.................... Boxes. applies to solid dry powders. [[Page 484]] PARTICULAR PACKING REQUIREMENTS paper, multiwall, water paper, multiwall, steel (4A). OR EXCEPTIONS: resistant. water resistant with natural wood, 1. For UN 0004, 0076, 0078, 0154, plastics................. inner lining. aluminum (4B). 0216, 0219 and 0386, packagings woven plastics........... plastics................ ordinary (4C1). must be lead free Receptacles.............. Receptacles............. natural wood, 2. For UN 0209, bags, sift-proof fibreboard............... metal................... sift proof (4C2). (5H2) are recommended for flake metal.................... plastics................ plywood (4D). or prilled TNT in the dry state. plastics................. reconstituted wood (4F). Bags must not exceed a maximum wood..................... fibreboard (4G). net mass of 30 kg. plastics, solid (4H2). 3. Inner packagings are not Drums. required if drums are used as plastics, removable head the outer packaging. (1H2). 4. At least one of the packagings steel, removable head must be sift-proof (1A2). aluminium, removable head (1B2). Plywood (1D). fibre (1G). 113.............................. Bags..................... Not necessary........... Boxes. PARTICULAR PACKING REQUIREMENTS paper.................. ........................ steel (4A). OR EXCEPTIONS: plastics................. aluminum (4B). 1. For UN 0094 and UN 0305, no textile, rubberized...... natural wood, ordinary more than 50 g of substance must Receptacles.............. (4C1). be packed in an inner packaging fibreboard............... natural wood, sift-proof 2. For UN 0027, inner packagings metal.................... walls (4C2). are not necessary when drums are plastics................. plywood (4D). used as the outer packaging wood..................... reconstituted wood (4F). 3. At least one of the packagings Sheets................... fibreboard (4G). must be sift- proof paper, kraft............. plastics, solid (4H2). 4. Sheets must only be used for paper, waxed............. Drums UN 0028 plastics, removable head (1H2). steel, removable head (1A2). aluminium, removable head (1B2). Plywood (1D). fibre (1G). 114(a) This packing instruction Bags..................... Bags.................... Boxes. applies to wetted solids. plastics................. plastics................ steel (4A). PARTICULAR PACKING REQUIREMENTS textile.................. textile, plastic coated natural wood, ordinary OR EXCEPTIONS:. woven plastics........... or lined. (4C1). 1. For UN 0077, 0234, 0235 and Receptacles.............. Receptacles............. natural wood, sift proof 0236, packagings must be lead metal.................... metal................... walls (4C2). free. plastics................. plastics................ plywood (4D). 2. For UN 0342, inner packagings reconstituted wood (4F). are not required when metal (1A2 fibreboard (4G). or 1B2) or plastics (1H2) drums plastics, solid (4H2). are used as outer packagings. Drums. 3. Intermediate packagings are steel, removable head not required if leakproof (1A2). removable head drums are used as aluminium, removable the outer packaging. head (1B2). plywood (1D). fibre (1G). plastics, removable head (1H2). 114(b) This packing instruction Bags..................... Not necessary........... Boxes. applies to dry solids. [[Page 485]] PARTICULAR PACKING REQUIREMENTS paper, kraft........... ........................ natural wood, ordinary OR EXCEPTIONS: plastics................. (4C1). 1. For UN 0077, 0132, 0234, 0235 textile, sift-proof...... natural wood, sift proof and 0236, packagings must be woven plastics, sift- walls (4C2) lead free proof. plywood (4D). 2. For UN 0160 and UN 0161, when Receptacles.............. reconstituted wood (4F). metal drums (1A2 or 1B2) are fibreboard............... fibreboard (4G). used as the outer packaging, metal.................... Drums. metal packagings must be so paper.................... steel, removable head constructed that the risk of plastics................. (1A2). explosion, by reason of woven plastics, sift- aluminium, removable increased internal pressure from proof. head (1B2) internal or external causes is plywood (1D). prevented fibre (1G). 3. For UN 0160 and UN 0161, inner plastics, removable head packagings are not required if (1H2) drums are used as the outer packaging 115.............................. Receptacles.............. Bags.................... Boxes. PARTICULAR PACKING REQUIREMENTS metal.................... plastics in metal natural wood, ordinary OR EXCEPTIONS: plastics................. receptacles. (4C1). 1. For liquid explosives, inner Drums................... natural wood, sift proof packagings must be surrounded metal................... walls (4C2). with non-combustible absorbent plywood (4D). cushioning material in reconstituted wood (4F). sufficient quantity to absorb fibreboard (4G). the entire liquid content. Metal Drums. receptacles should be cushioned plastics, removable head from each other. The net mass of (1H2). explosive per package may not steel, removable head exceed 30 kg when boxes are used (1A2). as outer packaging. The net aluminium, removable volume of explosive in each head (1B2). package other than boxes must plywood (1D). not exceed 120 litres fibre (1G). 2. For UN 0075, 0143, 0495 and Specification MC-200 0497 when boxes are used as the containers may be used outer packaging, inner for transport by motor packagings must have taped screw vehicle. cap closures and be not more than 5 litres capacity each. A composite packaging consisting of a plastic receptacle in a metal drum (6HA1) may be used in lieu of combination packagings. Liquid substances must not freeze at temperatures above -15 [deg]C (+5 [deg]F) 3. For UN 0144, intermediate packagings are not necessary. 116.............................. Bags..................... Not necessary........... Bags. [[Page 486]] PARTICULAR PACKING REQUIREMENTS paper, water and oil..... ........................ woven plastics (5H1/2/ OR EXCEPTIONS: resistant................ 3). 1. For UN 0082, 0241, 0331 and plastics................. paper, mulitwall, water 0332, inner packagings are not texitile, plasic coated resistant (5M2). necessary if leakproof removable or. plastics, film (5H4). head drums are used as the outer lined.................... textile, sift-proof packaging woven plasics, sift-proof (5L2). 2. For UN 0082, 0241, 0331 and Receptacles.............. textile, water resistant 0332, inner packagings are not fibreboard, water (5L3). required when the explosive is resistant. Boxes. contained in a material metal.................... steel (4A). impervious to liquid plastics................. aluminium (4B). 3. For UN 0081, inner packagings wood, sift-proof......... wood, natural, ordinary are not required when contained Sheets................... (4C1). in rigid plastic which is paper, water resistant... natural wood, sift proof impervious to nitric esters paper, waxed............. walls (4C2). 4. For UN 0331, inner packagings plastics................. plywood (4D). are not required when bags reconstituted wood (4F). (5H2), (5H3) or (5H4) are used fibreboard (4G). as outer packagings plastics, solid (4H2). 5. Bags (5H2 or 5H3) must be used Drums. only for UN 0082, 0241, 0331 and steel, removable head 0332 (1A2). 6. For UN 0081, bags must not be aluminium, removable used as outer packagings head (1B2). Plywood (1D). fibre (1G). plastics, removable head (1H2). Jerricans. steel, removable head (3A2). plastics, removable head (3H2). 117.............................. Not necessary............ Not necessary........... IBCs. PARTICULAR PACKING REQUIREMENTS ......................... ........................ metal (11A), (11B), OR EXCEPTIONS: (11N), (21A), (21B), 1. This packing instruction may (21N), (31A), (31B), only be used for explosives of (31N). 0082 when they are mixtures of flexible (13H2), (13H3), ammonium nitrate or other (13H4), (13L2), (13L3), inorganic nitrates with other (13L4), (13M2). combustible substances which are rigid plastics (11H1), not explosive ingredients. Such (11H2), (21H1), (21H2), explosives must not contain (31H1), (31H2). nitroglycerin, similar liquid composite (11HZ1), organic nitrates, liquid or (11HZ2), (21HZ1), solid nitrocarbons, or (21HZ2), (31HZ1), chlorates. (31HZ2). 2. This packing instruction may only be used for explosives of UN 0241 which consist of water as an essential ingredient and high proportions of ammonium nitrate or other oxidizers, some or all of which are in solution. The other constituents may include hydrocarbons or aluminium powder, but must not include nitro-derivatives such as trinitrotoluene. 3. Metal IBCs must not be used for UN 0082 and 0241. 4. Flexible IBCs may only be used for solids. 130.............................. Not necessary............ Not necessary........... Boxes. [[Page 487]] PARTICULAR PACKING REQUIREMENTS ......................... ........................ steel (4A). OR EXCEPTIONS: aluminium (4B). 1. The following applies to UN wood natural, ordinary 0006, 0009, 0010, 0015, 0016, (4C1). 0018, 0019, 0034, 0035, 0038, natural wood, sift proof 0039, 0048, 0056, 0137, 0138, walls (4C2). 0168, 0169, 0171, 0181, 0182, plywood (4D). 0183, 0186, 0221, 0238, 0243, reconstituted wood (4F). 0244, 0245, 0246, 0254, 0280, fibreboard (4G). 0281, 0286, 0287, 0297, 0299, plastics, expanded 0300, 0301, 0303, 0321, 0328, (4H1). 0329, 0344, 0345 0346, 0347, plastics, solid (4H2). 0362, 0363, 0370, 0412, 0424, Drums. 0425, 0434, 0435, 0436, 0437, steel, removable head 0438, 0451, 0459 and 0488. Large (1A2). and robust explosives articles, aluminium, removable normally intended for military head (1B2). use, without their means of Plywood (1D). initiation or with their means fibre (1G). of initiation containing at plastics, removable head least two effective protective (1H2). features, may be carried unpackaged. When such articles have propelling charges or are self-propelled, their ignition systems must be protected against stimuli encountered during normal conditions of transport. A negative result in Test Series 4 on an unpackaged article indicates that the article can be considered for transport unpackaged. Such unpackaged articles may be fixed to cradles or contained in crates or other suitable handling devices. 131.............................. Bags..................... Not necessary........... Boxes. PARTICULAR PACKING REQUIREMENTS ......................... ........................ steel (4A). OR EXCEPTIONS: paper.................... aluminium (4B). 1. For UN 0029, 0267 and 0455, plastics................. wood, natural, ordinary bags and reels may not be used Receptacles.............. (4C1). as inner packagings fibreboard............... natural wood, sift proof 2. For UN 0030, 0255 and 0456, metal.................... walls (4C2). inner packagings are not plastics................. plywood (4D). required when detonators are wood..................... reconstituted wood (4F). packed in pasteboard tubes, or Reels.................... fibreboard (4G). when their leg wires are wound Drums. on spools with the caps either steel, removable head placed inside the spool or (1A2). securely taped to the wire on aluminium, removable the spool, so as to restrict head (1B2). free moving of the caps and to Plywood (1D). protect them from impact forces fibre (1G). 3. For UN 0360, 0361 and 0500, plastics, removable head detonators are not required to (1H2). be attached to the safety fuse, metal-clad mild detonating cord, detonating cord, or shock tube. Inner packagings are not required if the packing configuration restricts free moving of the caps and protects them from impact forces 132(a) For articles consisting of Not necessary............ Not necessary........... Boxes. closed metal, plastic or steel (4A). fiberboard casings that contian aluminum (4B). detonating explosives, or wood, natural; ordinary consisting of plastics-bonded (4C1). detonating explosives. wood, natural, sift proof walls (4C2). plywood (4D). reconstituted wood (4F). fiberboard (4G). plastics, solid (4H2). 132(b) For articles without Receptacles fiberboard Not necessary........... Boxes. closed casings. metal plastics. Sheets steel (4A); aluminum paper plastics. (4B). wood, natural, ordinary (4C1). wood, natural, sift proof walls (4C2). plywood (4D). reconstituted wood (4F). fiberboard (4G). plastics, solid (4H2). [[Page 488]] 133.............................. Receptacles.............. Receptacles............. Boxes. PARTICULAR PACKING REQUIREMENTS Intermediate packagings fibreboard............ steel (4A). OR EXCEPTIONS: are only required when metal................... aluminium (4B). 1. For UN 0043, 0212, 0225, 0268 trays are used as inner plastics................ wood, natural, ordinary and 0306 trays are not packagings. wood.................... (4C1). authorized as inner packagings fibreboard............... wood, natural, sift metal.................... proof walls (4C2). plastics................. plywood (4D). wood..................... reconstituted wood (4F). Trays, fitted with fibreboard (4G). dividing. plastics, solid (4H2). partitions............... fibreboard............... plastics................. wood..................... 134.............................. Bags..................... Not necessary........... Boxes. water resistant.......... steel (4A). Receptacles.............. aluminium (4B). fibreboard............... wood, natural, ordinary metal.................... (4C1). plastics................. wood, natural, sift wood..................... proof walls (4C2). Sheets................... plywood (4D). fibreboard, corrugated... reconstituted wood (4F). Tubes.................... fibreboard (4G). fibreboard............... plastics, solid (4H2). Drums. fiberboard (1G). plastics, removable head (1H2). steel, removable head (1A2). aluminium, removable head (1B2). Plywood (1D). 135.............................. Bags..................... Not necessary........... Boxes. paper.................... steel (4A). plastics................. aluminium (4B). Receptacles.............. wood, natural, ordinary fibreboard............... (4C1). metal.................... wood, natural, sift plastics................. proof walls (4C2). wood..................... plywood (4D). Sheets................... reconstituted wood (4F). paper.................... fibreboard (4G). plastics................. plastics, expanded (4H1). plastics, solid (4H2). Drums. steel, removable head (1A2). aluminium, removable head (1B2). Plywood (1D). fibre (1G). plastics, removable head (1H2). [[Page 489]] 136.............................. Bags..................... Not necessary........... Boxes. plastics................. steel (4A). textile.................. aluminium (4B) Boxes.................... wood, natural, ordinary fibreboard............... (4C1). plastics................. wood, natural, sift wood..................... proof walls (4C2). Dividing partitions in plywood (4D). the. reconstituted wood (4F). outer packagings......... fibreboard (4G). plastics, solid (4H2). Drums. steel, removable head (1A2). aluminium, removable head (1B2). Plywood (1D). fibre (1G). plastics, removable head (1H2). 137 PARTICULAR PACKING Bags..................... Not necessary........... Boxes. REQUIREMENTS OR EXCEPTIONS: For plastics................. steel (4A). UN 0059, 0439, 0440 and 0441, Boxes.................... aluminium (4B). when the shaped charges are fibreboard............... wood, natural, ordinary packed singly, the conical Tubes.................... (4C1). cavity must face downwards and fibreboard............... wood, natural, sift the package marked ``THIS SIDE metal.................... proof walls (4C2). UP''. When the shaped charges plastics................. plywood (4D). are packed in pairs, the conical Dividing partitions in reconstituted wood (4F). cavities must face inwards to the outer packagings. fibreboard (4G). minimize the jetting effect in the event of accidental initiation. 138.............................. Bags..................... Not necessary........... Boxes. PARTICULAR PACKING REQUIREMENTS plastics............... ........................ steel (4A). OR EXCEPTIONS: aluminium (4B). If the ends of the articles are wood, natural, ordinary sealed, inner packagings are not (4C1). necessary wood, natural, sift proof walls (4C2). plywood (4D). reconstituted wood (4F). fibreboard (4G). plastics, solid (4H2). Drums. fiberboard (1G). plastics, removable head (1H2). steel, removable head (1A2). aluminium, removable head (1B2). 139.............................. Bags..................... Not necessary........... Boxes. [[Page 490]] PARTICULAR PACKING REQUIREMENTS plastics............... ........................ steel (4A). OR EXCEPTIONS: Receptacles.............. aluminium (4B). 1. For UN 0065, 0102, 0104, 0289 fibreboard............... wood, natural, ordinary and 0290, the ends of the metal.................... (4C1). detonating cord must be sealed, plastics................. wood, natural, sift for example, by a plug firmly wood..................... proof walls (4C2). fixed so that the explosive Reels.................... plywood (4D). cannot escape. The ends of CORD ......................... reconstituted wood (4F). DETONATING flexible must be Sheets................... fibreboard (4G). fastened securely paper.................... plastics, solid (4H2). 2. For UN 0065 and UN 0289, inner plastics................. Drums. packagings are not required when steel, removable head they are fastened securely in (1A2). coils aluminium, removable head (1B2). plywood (1D). fibre (1G). plastics, removable head (1H2). 140.............................. Bags..................... Not necessary........... Boxes. PARTICULAR PACKING REQUIREMENTS plastics............... ........................ steel (4A). OR EXCEPTIONS: Reels.................... aluminium (4B). 1. If the ends of UN 0105 are Sheets................... wood, natural, ordinary sealed, no inner packagings are paper, kraft............. (4C1). required plastics................. wood, natural, sift 2. For UN 0101, the packaging proof walls (4C2). must be sift-proof except when plywood (4D). the fuse is covered by a paper reconstituted wood (4F). tube and both ends of the tube fibreboard (4G). are covered with removable caps plastics, solid (4H2). 3. For UN 0101, steel or Drums. aluminium boxes or drums must plastics, removable head not be used (1H2). steel, removable head (1A2). aluminium, removable head (1B2). Plywood (1D). fibre (1G). 141.............................. Receptacles.............. Not necessary........... Boxes. fibreboard............... steel (4A). metal.................... aluminium (4B). plastics................. wood, natural, ordinary wood..................... (4C1). ......................... wood, natural, sift Trays, fitted with proof walls (4C2). dividing partitions. plywood (4D). plastics................. reconstituted wood (4F). wood..................... fibreboard (4G). Dividing partitions in plastics, solid (4H2). the outer packagings. Drums. steel, removable head (1A2). aluminium, removable head (1B2). Plywood (1D). fibre (1G). plastics, removable head (1H2). [[Page 491]] 142.............................. Bags..................... Not necessary........... Boxes. paper.................... steel (4A). plastics................. aluminium (4B). Receptacles.............. wood, natural, ordinary fibreboard............... (4C1). metal.................... wood, natural, sift plastics................. proof walls (4C2). wood..................... plywood (4D). Sheets................... reconstituted wood (4F). paper.................... fibreboard (4G). Trays, fitted with plastics, solid (4H2). dividing partitions. Drums. plastics................. steel, removable head (1A2). aluminium, removable head (1B2). Plywood (1D). fibre (1G). plastics, removable head (1H2). 143.............................. Bag...................... Not necessary........... Boxes. PARTICULAR PACKING REQUIREMENTS paper, kraft........... ........................ steel (4A). OR EXCEPTIONS: plastics................. aluminum (4B). 1. For UN 0271, 0272, 0415 and textile.................. wood, natural, ordinary 0491 when metal packagings are textile, rubberized...... (4C1). used, metal packagings must be Receptacles.............. wood, natural, sift so constructed that the risk of fibreboard............... proof walls (4C2). explosion, by reason of increase metal.................... plywood (4D). in internal pressure from plastics................. reconstituted wood (4F). internal or external causes is Trays, fitted with fibreboard (4G). prevented dividing partitions. plastics, solid (4H2). 2. Composite packagings (6HH2) plastics................. Drums. (plastic receptacle with outer wood..................... steel, removable head solid box) may be used in lieu (1A2). of combination packagings aluminium, removable head (1B2). plywood (1D). fibre (1G). plastics, removable head (1H2). 144.............................. Receptacles.............. Not necessary........... Boxes. Drums. steel, removable head (1A2). aluminium, removable head (1B2). plastics, removable head (1H2). Plywood (1D). PARTICULAR PACKING REQUIREMENTS fibreboard............. ........................ 2steel (4A). OR EXCEPTIONS: metal.................... aluminum (4B). For UN 0248 and UN 0249, plastics................. wood, natural, ordinary packagings must be protected Dividing partitions in (4C1) with metal liner. against the ingress of water. the outer packagings. plywood (4D) with metal When CONTRIVANCES, WATER liner. ACTIVATED are transported reconstituted wood (4F) unpackaged, they must be with metal liner. provided with at least two plastics, expanded independent protective features (4H1). which prevent the ingress of plastics, solid (4H2). water US 1 1. A jet perforating gun, charged, oil well may be transported under the following conditions:................ [[Page 492]] a. Initiation devices carried on the same motor vehicle or offshore supply vessel must be segregated; each kind from every other kind, and from any gun, tool or other supplies, unless approved in accordance with Sec. 173.56. Segregated initiation devices must be carried in a container having individual pockets for each such device or in a fully enclosed steel container lined with a non-sparking material. No more than two segregated initiation devices per gun may be carried on the same motor vehicle.. b. Each shaped charge affixed to the gun may not contain more than 112 g (4 ounces) of explosives............. c. Each shaped charge if not completely enclosed in glass or metal, must be fully protected by a metal cover after installation in the gun.. d. A jet perforating gun classed as 1.1D or 1.4D may be transported by highway by private or contract carriers engaged in oil well operations.. (i) A motor vehicle transporting a gun must have specially built racks or carrying cases designed and constructed so that the gun is securely held in place during transportation and is not subject to damage by contact, one to the other or any other article or material carried in the vehicle; and. (ii) The assembled gun packed on the vehicle may not extend beyond the body of the motor vehicle.............. e. A jet perforating gun classed as 1.4D may be transported by a private offshore supply vessel only when the gun is carried in a motor vehicle as specified in paragraph (d) of this packing method or on offshore well tool pallets provided that:. (i) All the conditions specified in paragraphs (a), (b), and (c) of this packing method are met;.............. (ii) The total explosive contents do not exceed 90.8 kg (200 pounds) per tool pallet;......................... (iii) Each cargo vessel compartment may contain up to 90.8 kg (200 pounds) of explosive content if the segregation requirements in Sec. 176.83(b) of this subchapter are met; and. (iv) When more than one vehicle or tool pallet is stowed ``on deck'' a minimum horizontal separation of 3 m (9.8 feet) must be provided.. ---------------------------------------------------------------------------------------------------------------- [Amdt. 173-260, 62 FR 24720, May 6, 1997; 62 FR 45702, Aug. 28, 1997; 62 FR 51560, Oct. 1, 1997; 63 FR 1884, Jan. 12, 1998; 63 FR 52849, Oct. 1, 1998; 64 FR 51918, Sept. 27, 1999; 65 FR 50461, Aug. 18, 2000; 65 FR 58629, Sept. 29, 2000; 65 FR 60383, Oct. 11, 2000; 66 FR 33429, 33430, June 21, 2001; 66 FR 45183, 45379, 45382, Aug. 28, 2001; 68 FR 45033, July 31, 2003; 68 FR 48569, Aug. 14, 2003; 68 FR 61941, Oct. 30, 2003]