[Code of Federal Regulations] [Title 40, Volume 28] [Revised as of July 1, 2006] From the U.S. Government Printing Office via GPO Access [CITE: 40CFR414.101] [Page 237] TITLE 40--PROTECTION OF ENVIRONMENT CHAPTER I--ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PART 414_ORGANIC CHEMICALS, PLASTICS, AND SYNTHETIC FIBERS--Table of Contents Subpart J_Direct Discharge Point Sources That Do Not Use End-of-Pipe Biological Treatment Sec. 414.101 Toxic pollutant effluent limitations and standards for direct discharge point sources that do not use end-of-pipe biological treatment. (a)Any point source subject to this subpart must achieve discharges not exceeding the quantity (mass) determined by multiplying the process wastewater flow subject to this subpart times the concentartions in the following table. (b) In the case of chromium, copper, lead, nickel, zinc, and total cyanide, the discharge quantity (mass) shall be determined by multiplying the concentrations listed in the following table for these pollutants times the flow from metal bearing waste streams for the metals and times the cyanide-bearing waste streams for total cyanide. The metal-bearing waste streams and cyanide-bearing waste streams are defined as those waste streams listed in Appendix A of this part, plus any additional OCPSF process wastewater streams identified by the permitting authority on a case-by-case basis as metal or cyanide bearing based upon a determination that such streams contain significant amounts of the pollutants identified above. Any such streams designated as metal or cyanide bearing must be treated independently of other metal or cyanide bearing waste streams unless the permitting authority determines that the combination of such streams, prior to treatment, with the Appendix A waste streams will result in substantial reduction of these pollutants. This determination must be based upon a review of relevant engineering, production, and sampling and analysis information. ------------------------------------------------------------------------ BAT effluent limitations and NSPS \1\ --------------------- Effluent characteristics Maximum Maximum for for any monthly one day average ------------------------------------------------------------------------ Acenaphthene...................................... 47 19 Acenaphthylene.................................... 47 19 Acrylonitrile..................................... 232 94 Anthracene........................................ 47 19 Benzene........................................... 134 57 Benzo(a)anthracene................................ 47 19 3,4-Benzofluoranthene............................. 48 20 Benzo(k)fluoranthene.............................. 47 19 Benzo(a)pyrene.................................... 48 20 Bis(2-ethylhexyl) phthalate....................... 258 95 Carbon Tetrachloride.............................. 380 142 Chlorobenzene..................................... 380 142 Chloroethane...................................... 295 110 Chloroform........................................ 325 111 Chrysene.......................................... 47 19 Di-n-butyl phthalate.............................. 43 20 1,2-Dichlorobenzene............................... 794 196 1,3-Dichlorobenzene............................... 380 142 1,4-Dichlorobenzene............................... 380 142 1,1-Dichloroethane................................ 59 22 1,2-Dichloroethane................................ 574 180 1,1-Dichloroethylene.............................. 60 22 1,2-trans-Dichloroethylene........................ 66 25 1,2-Dichloropropane............................... 794 196 1,3-Dichloropropylene............................. 794 196 Diethyl phthalate................................. 113 46 2,4-Dimethylphenol................................ 47 19 Dimethyl phthalate................................ 47 19 4,6-Dinitro-o-cresol.............................. 277 78 2,4-Dinitrophenol................................. 4,291 1,207 Ethylbenzene...................................... 380 142 Fluoranthene...................................... 54 22 Fluorene.......................................... 47 19 Hexachlorobenzene................................. 794 196 Hexachlorobutadiene............................... 380 142 Hexachloroethane.................................. 794 196 Methyl Chloride................................... 295 110 Methylene Chloride................................ 170 36 Naphthalene....................................... 47 19 Nitrobenzene...................................... 6,402 2,237 2-Nitrophenol..................................... 231 65 4-Nitrophenol..................................... 576 162 Phenanthrene...................................... 47 19 Phenol............................................ 47 19 Pyrene............................................ 48 20 Tetrachloroethylene............................... 164 52 Toluene........................................... 74 28 Total Chromium.................................... 2,770 1,110 Total Copper...................................... 3,380 1,450 Total Cyanide..................................... 1,200 420 Total Lead........................................ 690 320 Total Nickel...................................... 3,980 1,690 Total Zinc \2\.................................... 2,610 1,050 1,2,4-Trichlorobenzene............................ 794 196 1,1,1-Trichloroethane............................. 59 22 1,1,2-Trichloroethane............................. 127 32 Trichloroethylene................................. 69 26 Vinyl Chloride.................................... 172 97 ------------------------------------------------------------------------ \1\ All units are micrograms per liter. \2\ Total Zinc for Rayon Fiber Manufacture that uses the viscose process and Acrylic Fibers Manufacture that uses the zinc chloride/solvent process is 6,796 [micro]g/l and 3,325 [micro]g/l for maximum for any one day and maximum for monthly average, respectively. [52 FR 42568, Nov. 5, 1987, as amended at 58 FR 36893, July 9, 1993] [[Page 238]]