[Code of Federal Regulations] [Title 40, Volume 12] [Revised as of July 1, 2006] From the U.S. Government Printing Office via GPO Access [CITE: 40CFR63.1451] [Page 38-40] TITLE 40--PROTECTION OF ENVIRONMENT CHAPTER I--ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PART 63_NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES--Table of Contents Subpart QQQ_National Emission Standards for Hazardous Air Pollutants for Primary Copper Smelting Sec. 63.1451 How do I demonstrate initial compliance with the emission limitations, work practice standards, and operation and maintenance requirements that apply to me? (a) Total particulate matter emission limits. For each copper concentrate dryer, smelting furnace, slag cleaning vessel, and copper converter department subject to a total particulate matter emission limits in Sec. 63.1444 or Sec. 63.1446 that applies to you, you have demonstrated initial compliance if you meet both of the conditions in paragraphs (a)(1) and (2) of this section. [[Page 39]] (1) The average concentration of total particulate matter from a control device applied to emissions from the affected source, measured according to the performance test procedures in Sec. 63.1450(a), did not exceed the applicable emission limit. (2) You have submitted a notification of compliance status according to the requirements in Sec. 63.1454(e). (b) Nonsulfuric acid particulate matter emissions limits. For each smelting furnace, slag cleaning vessel, and copper converter departments subject to the nonsulfuric acid particulate matter emissions limit in Sec. 63.1444 as applies to you, you have demonstrated initial compliance if you meet both of the conditions in paragraphs (b)(1) and (2) of this section. (1) The average concentration of nonsulfuric acid particulate matter in the process off-gas discharged from the affected source, measured according to the performance test procedures in Sec. 63.1450(b), did not exceed 6.2 mg/dscm. (2) You have submitted a notification of compliance status according to the requirements in Sec. 63.1454(e). (c) For each existing copper converter department subject to the opacity limit in Sec. 63.1444, you have demonstrated initial compliance if you meet both of the conditions in paragraphs (c)(1) and (2) of this section. (1) The opacity of visible emissions exiting the roof monitors or roof exhaust fans on the building housing the copper converter department measured according to the performance test procedures in Sec. 63.1450(c), did not exceed 4 percent opacity. (2) You have submitted a notification of compliance status according to the requirements in Sec. 63.1454(e). (d) Copper converter department capture systems. You have demonstrated initial compliance of the copper converter department capture system if you meet all of the conditions in paragraphs (d)(1) through (4) of this section. (1) Prepared the capture system operation and maintenance plan according to the requirements of paragraph (a) of this section; (2) Conducted an initial performance test according to the procedures of Sec. 63.1450(c) demonstrating the opacity of any visible emissions exiting the roof monitors or roof exhaust fans on the building housing the copper converter department does not exceed 4 percent opacity; (3) Included in your notification of compliance status a copy of your written capture system operation and maintenance plan and have certified in your notification of compliance status that you will operate the copper converter department capture system at all times during blowing at the values or settings established for the operating limits in that plan; and (4) Submitted a notification of compliance status according to the requirements in Sec. 63.1454(e). (e) Baghouses. For each baghouse subject to operating limits in Sec. 63.1444(f) or Sec. 63.1446(c), you have demonstrated initial compliance if you meet all of the conditions in paragraphs (e)(1) through (3) of this section. (1) You have included in your written operation and maintenance plan required under Sec. 63.1447(b) detailed descriptions of the procedures you use for inspection, maintenance, bag leak detection, and corrective action for the baghouse. (2) You have certified in your notification of compliance status that you will operate the baghouse according to your written operation and maintenance plan. (3) You have submitted the notification of compliance status according to the requirements in Sec. 63.1454(e). (f) Venturi wet scrubbers. For each venturi wet scrubber subject to operating limits in Sec. 63.1444(g) or Sec. 63.1446(d), you have demonstrated initial compliance if you meet all of the conditions in paragraphs (f)(1) through (3) of this section. (1) Established site-specific operating limits for pressure drop and scrubber water flow rate and have a record of the pressure drop and scrubber water flow rate measured during the performance test you conduct to demonstrate initial compliance with paragraph (a) of this section. (2) Certified in your notification of compliance status that you will operate the venturi wet scrubber within the established operating limits for pressure drop and scrubber water flow rate. [[Page 40]] (3) Submitted a notification of compliance status according to the requirements in Sec. 63.1454(e). (g) Other control devices. For each control device other than a baghouse or venturi wet scrubber subject to operating limits in Sec. 63.1444(h) or Sec. 63.1446(e), you have demonstrated initial compliance if you meet all of the conditions in paragraphs (g)(1) through (4) of this section. (1) Selected one or more operating parameters, as appropriate for the control device design, that can be used as representative and reliable indicators of the control device operation. (2) Established site-specific operating limits for each of the selected operating parameters based on values measured during the performance test you conduct to demonstrate initial compliance with paragraph (a) of this section and have prepared written documentation according to the requirements in Sec. 63.1450(a)(5)(iv). (3) Included in your notification of compliance status a copy of the written documentation you have prepared to demonstrate compliance with paragraph (g)(2) of this section and have certified in your notification of compliance status that you will operate the control device within the established operating limits. (4) Submitted a notification of compliance status according to the requirements in Sec. 63.1454(e). (h) Fugitive dust sources. For all fugitive dust sources subject to work practice standards in Sec. 63.1445, you have demonstrated initial compliance if you meet all of the conditions in paragraphs (i)(1) through (3) of this section. (1) Prepared a written fugitive dust control plan according to the requirements in Sec. 63.1454 and it has been approved by the designated authority. (2) Certified in your notification of compliance status that you will control emissions from the fugitive dust sources according to the procedures in the approved plan. (3) Submitted the notification of compliance status according to the requirements in Sec. 63.1454(e). (i) Operation and maintenance requirements. You have demonstrated initial compliance with the operation and maintenance requirements that apply to you if you meet all of the conditions in paragraphs (i)(1) through (3) of this section. (1) Prepared an operation and maintenance plan according to the requirements in Sec. 63.1454(b). (2) Certified in your notification of compliance status that you will operate each capture system and control device according to the procedures in the plan. (3) Submitted the notification of compliance status according to the requirements in Sec. 63.1454(e). Continuous Compliance Requirements