[Code of Federal Regulations] [Title 49, Volume 2] [Revised as of October 1, 2006] From the U.S. Government Printing Office via GPO Access [CITE: 49CFR174.67] [Page 701-704] TITLE 49--TRANSPORTATION CHAPTER I--PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PART 174_CARRIAGE BY RAIL--Table of Contents Subpart C_General Handling and Loading Requirements Sec. 174.67 Tank car unloading. For transloading operations, the following rules must be observed: (a) General requirements. (1) Unloading operations must be performed by hazmat employees properly instructed in unloading hazardous materials and made responsible for compliance with this section. (2) The unloader must apply the handbrake and block at least one wheel to prevent movement in any direction. If multiple tank cars are coupled together, sufficient hand brakes must be set and wheels blocked to prevent movement in both directions. (3) The unloader must secure access to the track to prevent entry by other rail equipment, including motorized service vehicles. This requirement may [[Page 702]] be satisfied by lining each switch providing access to the unloading area against movement and securing each switch with an effective locking device, or by using derails, portable bumper blocks, or other equipment that provides an equivalent level of safety. (4) The unloader must place caution signs on the track or on the tank cars to warn persons approaching the cars from the open end of the track that a tank car is connected to unloading equipment. The caution signs must be of metal or other durable material, rectangular, at least 30 cm (12 inches) high by 38 cm (15 inches) wide, and bear the word ``STOP''. The word ``STOP'' must appear in letters at least 10 cm (3.9 inches) high. The letters must be white on a blue background. Additional wording, such as ``Tank Car Connected'' or ``Crew at Work'' may also appear. (5) The transloading facility operator must maintain written safety procedures (such as those it may already be required to maintain pursuant to the Department of Labor's Occupational Safety and Health Administration requirements in 29 CFR 1910.119 and 1910.120) in a location where they are immediately available to hazmat employees responsible for the transloading operation. (b) After the pressure is released, the seal must be broken and the manhole cover removed as follows: (1) Screw type. The cover must be loosened by placing a bar between the manhole cover lug and knob. After two complete turns, so that vent openings are exposed, the operation must be stopped, and if there is any sound of escaping vapor, the cover must be screwed down tightly and the interior pressure relieved as prescribed in paragraph (a)(4) of this section, before again attempting to remove the cover. (2) Hinged and bolted type. All nuts must be unscrewed one complete turn, after which same precautions as prescribed for screw type cover must be observed. (3) Interior type. All dirt and cinders must be carefully removed from around the cover before the yoke is unscrewed. (c) When the car is unloaded through a bottom outlet valve, the manhole cover must be adjusted as follows: (1) Screw type. The cover must be put in place, but not entirely screwed down, so that air may enter the tank through the vent holes in threaded flange of the cover. (2) Hinged and bolted type. A non-metallic block must be placed under one edge of the cover. (3) Interior type. The screw must be tightened up in the yoke so that the cover is brought up within one-half inch of the closed position. (d) When unloading through the bottom outlet of a car equipped with an interior manhole type cover, and in each case where unloading is done through the manhole (unless a special cover with a safety vent opening and a tight connection for the discharge outlet is used), the manhole must be protected by asbestos or metal covers against the entrance of sparks or other sources of ignition of vapor, or by being covered and surrounded with wet burlap or similar cloth material. The burlap or other cloth must be kept damp by the replacement or the application of water as needed. (e) Seals or other substances must not be thrown into the tank and the contents may not be spilled over the car or tank. (f) The valve rod handle or control in the dome must be operated several times to see that outlet valve in bottom of tank is on its seat before valve cap is removed. (g) The valve cap, or the reducer when a large outlet is to be used, must be removed with a suitable wrench after the set screws are loosened and a pail must be placed in position to catch any liquid that may be in the outlet chamber. If the valve cap or reducer does not unscrew easily, it may be tapped lightly with a mallet or wooden block in an upward direction. If leakage shows upon starting the removal, the cap or reducer may not be entirely unscrewed. Sufficient threads must be left engaged and sufficient time allowed to permit controlled escape of any accumulation of liquid in the outlet chamber. If the leakage stops or the rate of leakage diminishes materially, the cap or reducer may be entirely removed. If the initial rate of leakage continues, further efforts must be [[Page 703]] made to seat the outlet valve (see paragraph (f) of this section). If this fails, the cap or reducer must be screwed up tight and the tank must be unloaded through the dome. If upon removal of the outlet cap the outlet chamber is found to be blocked with frozen liquid or any other matter, the cap must be replaced immediately and a careful examination must be made to determine whether the outlet casting has been cracked. If the obstruction is not frozen liquid, the car must be unloaded through the dome. If the obstruction is frozen liquid and no crack has been found in the outlet casting, the car may, if circumstances require it, be unloaded from the bottom by removing the cap and attaching unloading connections immediately. Before opening the valve inside the tank car, steam must be applied to the outside of the outlet casting or wrap casting with burlap or other rags and hot water must be applied to melt the frozen liquid. (h) Unloading connections must be securely attached to unloading pipes on the dome or to the bottom discharge outlets before any discharge valves are opened. (i) Throughout the entire period of unloading and while a tank car has unloading equipment attached, the facility operator must assure that the tank car is: (1) Attended by a designated hazmat employee who is physically present and who has an unobstructed view of the unloading operation; or (2) Monitored by a signaling system (e.g., video system, sensing equipment, or mechanical equipment) that is observed by a designated hazmat employee located either in the immediate area of the tank car or at a remote location within the facility, such as a control room. The signaling system must-- (i) Provide a level of surveillance equivalent to that provided in subparagraph (1) of this paragraph (i); and (ii) Provide immediate notification to a designated hazmat employee of any system malfunction or other emergency so that, if warranted, responsive actions may be initiated immediately. (j) Attendance is not required when piping is attached to a top outlet of a tank car, equipped with a protective housing required under Sec. 179.100-12 of this subchapter, for discharge of lading under the following conditions: (1) All valves are tightly closed. (2) The piping is not connected to hose or other unloading equipment and is fitted with a cap or plug of appropriate material and construction. (3) The piping extends no more than 15.24 centimeters (6 inches) from the outer edge of the protective housing. (k) In the absence of the unloader, a tank car may stand with unloading connections attached when no product is being transferred under the following conditions: (1) The facility operator must designate a hazmat employee responsible for on-site monitoring of the transfer facility. The designated hazmat employee must be made familiar with the nature and properties of the product contained in the tank car; procedures to be followed in the event of an emergency; and, in the event of an emergency, have the ability and authority to take responsible actions. (2) When a signaling system is used in accordance with paragraph (i) of this section, the system must be capable of alerting the designated hazmat employee in the event of an emergency and providing immediate notification of any monitoring system malfunction. If the monitoring system does not have self-monitoring capability, the designated hazmat employee must check the monitoring system hourly for proper operation. (3) The tank car and facility shutoff valves must be secured in the closed position. (4) Brakes must be set and wheels locked in accordance with paragraph (a)(2) of this section. (5) Access to the track must be secured in accordance with paragraph (a)(3) of this section. (l) As soon as a tank car is completely unloaded, all valves must be made tight by the use of a bar, wrench or other suitable tool, the unloading connections must be removed and all other closures made tight. (m) Railroad defect cards may not be removed. (n) If oil or gasoline has been spilled on the ground around connections, it [[Page 704]] must be covered with fresh, dry sand or dirt. (o) All tools and implements used in connection with unloading must be kept free of oil, dirt, and grit. [Amdt. 174-26, 41 FR 16092, Apr. 15, 1976, as amended by Amdt. 174-26A, 41 FR 40685, Sept. 20, 1976; Amdt. 174-43, 48 FR 27699, June 16, 1983; Amdt. 174-68, 55 FR 52678, Dec. 21, 1990; 56 FR 66280, Dec. 20, 1991; Amdt. 174-81, 60 FR 49111, Sept. 21, 1995; Amdt. 174-83, 61 FR 28678, June 5, 1996; 68 FR 61941, Oct. 30, 2003; 70 FR 20034, Apr. 15, 2005]