[Code of Federal Regulations]
[Title 40, Volume 31]
[Revised as of July 1, 2007]
From the U.S. Government Printing Office via GPO Access
[CITE: 40CFR1051.515]
[Page 649-653]
TITLE 40--PROTECTION OF ENVIRONMENT
CHAPTER I--ENVIRONMENTAL PROTECTION AGENCY (CONTINUED)
PART 1051_CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES
AND VEHICLES--Table of Contents
Subpart F_Test Procedures
Sec. 1051.515 How do I test my fuel tank for permeation emissions?
Measure permeation emissions by weighing a sealed fuel tank before
and after a temperature-controlled soak.
(a) Preconditioning fuel soak. To precondition your fuel tank,
follow these five steps:
(1) Fill the tank with the fuel specified in Sec.
1051.501(d)(2)(i), seal it, and allow it to soak at 28 5 [deg]C for 20 weeks. Alternatively, the tank may be
soaked for a shorter period of time at a higher temperature if you can
show that the hydrocarbon permeation rate has stabilized.
(2) Determine the fuel tank's internal surface area in square-meters
accurate to at least three significant figures. You may use less
accurate estimates of the surface area if you make sure not to
overestimate the surface area.
(3) Fill the fuel tank with the test fuel specified in Sec.
1051.501(d)(2)(ii) to its nominal capacity. If you fill the tank inside
the temperature-controlled room or enclosure, do not spill any fuel.
(4) Allow the tank and its contents to equilibrate to 28 2 [deg]C.
(5) Seal the fuel tank using fuel caps and other fittings (excluding
petcocks) that can be used to seal openings in a production fuel tank.
In cases where openings are not normally sealed on the fuel tank (such
as hose-connection fittings and vents in fuel caps), these openings may
be sealed using nonpermeable fittings such as metal or fluoropolymer
plugs.
(b) Permeation test run. To run the test, take the following steps
for a tank that was preconditioned as specified in paragraph (a) of this
section:
(1) Weigh the sealed fuel tank and record the weight to the nearest
0.1 grams. You may use less precise weights as long as the difference in
mass from the start of the test to the end of the test has at least
three significant figures. Take this measurement within 8 hours of
filling the tank with test fuel as specified in paragraph (a)(3) of this
section.
[[Page 650]]
(2) Carefully place the tank within a ventilated, temperature-
controlled room or enclosure. Do not spill or add any fuel.
(3) Close the room or enclosure and record the time.
(4) Ensure that the measured temperature in the room or enclosure is
28 2 [deg]C.
(5) Leave the tank in the room or enclosure for 14 days.
(6) Hold the temperature of the room or enclosure to 28 2 [deg]C; measure and record the temperature at least
daily.
(7) At the end of the soak period, weigh the sealed fuel tank and
record the weight to the nearest 0.1 grams. You may use less precise
weights as long as the difference in mass from the start of the test to
the end of the test has at least three significant figures. Unless the
same fuel is used in the preconditioning fuel soak and the permeation
test run, record weight measurements on five separate days per week of
testing. The test is void if a linear plot of tank weight vs. test days
for the full soak period for permeation testing specified in paragraph
(b)(5) of this section yields r\2\ below 0.8. See 40 CFR 1065.602 for
the equation to calculate r\2\.
(8) Subtract the weight of the tank at the end of the test from the
weight of the tank at the beginning of the test; divide the difference
by the internal surface area of the fuel tank. Divide this g/m\2\ value
by the number of test days (using at least three significant figures) to
calculate the g/m\2\/day emission rate. Example: If a tank with an
internal surface area of 0.72 m\2\ weighed 31882.3 grams at the
beginning of the test and weighed 31813.8 grams after soaking for 14.03
days, then the g/m\2\/day emission rate would be--
(31882.3 g-31813.8 g)/0.72 m\2\/14.03 days = 6.78 g/m\2\/day.
(9) Round your result to the same number of decimal places as the
emission standard.
(10) In cases where consideration of permeation rates, using good
engineering judgment, leads you to conclude that soaking for 14 days is
not long enough to measure weight change to at least three significant
figures, you may soak for 14 days longer. In this case, repeat the steps
in paragraphs (b)(8) and (9) of this section to determine the weight
change for the full 28 days.
(c) Determination of final test result. To determine the final test
result, apply a deterioration factor to the measured emission level. The
deterioration factor is the difference between permeation emissions
measured before and after the durability testing described in paragraph
(d) of this section. Adjust the baseline test results for each tested
fuel tank by adding the deterioration factor to the measured emissions.
The deterioration factor determination must be based on good engineering
judgement. Therefore, during the durability testing, the test tank may
not exceed the fuel tank permeation standard described in Sec. 1051.110
(this is known as ``line-crossing''). If the deterioration factor is
less than zero, use zero.
(d) Durability testing. You normally need to perform a separate
durability demonstration for each substantially different combination of
treatment approaches and tank materials. Perform these demonstrations
before an emission test by taking the following steps, unless you can
use good engineering judgment to apply the results of previous
durability testing with a different fuel system. You may ask to exclude
any of the following durability tests if you can clearly demonstrate
that it does not affect the emissions from your fuel tank.
(1) Pressure cycling. Perform a pressure test by sealing the tank
and cycling it between +2.0 psig and -0.5 psig and back to +2.0 psig for
10,000 cycles at a rate 60 seconds per cycle.
(2) UV exposure. Perform a sunlight-exposure test by exposing the
tank to an ultraviolet light of at least 24 W/m\2\ (0.40 W-hr/m\2\/min)
on the tank surface for at least 450 hours. Alternatively, the fuel tank
may be exposed to direct natural sunlight for an equivalent period of
time, as long as you ensure that the tank is exposed to at least 450
daylight hours.
(3) Slosh testing. Perform a slosh test by filling the tank to 40
percent of its capacity with the fuel specified in Sec.
1051.501(d)(2)(i) and rocking it at a rate of 15 cycles per minute until
you reach one million total cycles. Use an angle deviation of +15[deg]
to -15[deg] from
[[Page 651]]
level. This test must be performed at a temperature of 28 [deg]C 5 [deg]C.
(4) Final test result. Following the durability testing, the fuel
tank must be soaked (as described in paragraph (a) of this section) to
ensure that the permeation rate is stable. The period of slosh testing
and the period of ultraviolet testing (if performed with fuel in the
tank consistent with paragraph (a)(1) of this section) may be considered
to be part of this soak, provided that the soak begins immediately after
the slosh testing. To determine the final permeation rate, drain and
refill the tank with fresh fuel, and repeat the permeation test run (as
described in paragraph (b) of this section) immediately after this soak
period. The same test fuel must be used for this permeation test run as
for the permeation test run performed prior to the durability testing.
(e) Flow chart. The following figure presents a flow chart for the
permeation testing described in this section, showing the full test
procedure with durability testing, as well as the simplified test
procedure with an applied deterioration factor:
[[Page 652]]
[GRAPHIC] [TIFF OMITTED] TR15JA04.002
[[Page 653]]
[67 FR 68347, Nov. 8, 2002, as amended at 69 FR 2442, Jan. 15, 2004; 70
FR 40501, July 13, 2005]