[Code of Federal Regulations] [Title 49, Volume 6] [Revised as of October 1, 2007] From the U.S. Government Printing Office via GPO Access [CITE: 49CFR571.114] [Page 379-381] TITLE 49--TRANSPORTATION OF TRANSPORTATION PART 571_FEDERAL MOTOR VEHICLE SAFETY STANDARDS--Table of Contents Subpart B_Federal Motor Vehicle Safety Standards Sec. 571.114 Standard No. 114; Theft protection and rollaway prevention. S1. Scope. This standard specifies vehicle performance requirements intended to reduce the incidence of crashes resulting from theft and accidental rollaway of motor vehicles. S2. Purpose. The purpose of this standard is to decrease the likelihood that a vehicle is stolen, or accidentally set in motion. S3. Application. This standard applies to all passenger cars, and to trucks and multipurpose passenger vehicles with a GVWR of 4,536 kilograms (10,000 pounds) or less. However, it does not apply to walk-in van-type vehicles. S4. Definitions. Combination means a variation of the key that permits the starting system of a particular vehicle to be operated. Key means a physical device or an electronic code which, when inserted into the starting system (by physical or electronic means), enables the vehicle operator to activate the engine or motor. Open-body type vehicle means a vehicle having no occupant compartment doors or vehicle having readily detachable occupant compartment doors. Starting system means the vehicle system used in conjunction with the key to activate the engine or motor. Vehicle type, as used in S5.1.2, refers to passenger car, truck, or multipurpose passenger vehicle, as those terms are defined in 49 CFR 571.3. S5. Requirements. Each vehicle subject to this standard must meet the requirements of S5.1 and S5.2. Open-body type vehicles are not required to comply with S5.1.3. S5.1 Theft protection. S5.1.1 Each vehicle must have a starting system which, whenever the key is removed from the starting system prevents: [[Page 380]] (a) The normal activation of the vehicle's engine or motor; and (b) Either steering, or forward self-mobility, of the vehicle, or both. S5.1.2 For each vehicle type manufactured by a manufacturer, the manufacturer must provide at least 1,000 unique key combinations, or a number equal to the total number of the vehicles of that type manufactured by the manufacturer, whichever is less. The same combinations may be used for more than one vehicle type. S5.1.3 Except as specified below, an audible warning to the vehicle operator must be activated whenever the key is in the starting system and the door located closest to the driver's designated seating position is opened. An audible warning to the vehicle operator need not activate: (a) After the key has been inserted into the starting system, and before the driver takes further action; or (b) If the key is in the starting system in a manner or position that allows the engine or motor to be started or to continue operating; or (c) For mechanical keys and starting systems, after the key has been withdrawn to a position from which it may not be turned. S5.1.4 If a vehicle is equipped with a transmission with a ``park'' position, the means for deactivating the vehicle's engine or motor must not activate any device installed pursuant to S5.1.1(b), unless the transmission is locked in the ``park'' position. S5.2 Rollaway prevention in vehicles equipped with transmissions with a ``park'' position. S5.2.1 Except as specified in S5.2.3, the starting system required by S5.1 must prevent key removal when tested according to the procedures in S6, unless the transmission or gear selection control is locked in ``park'' or becomes locked in ``park'' as a direct result of key removal. S5.2.2 Except as specified in S5.2.4, the vehicle must be designed such that the transmission or gear selection control cannot move from the ``park'' position, unless the key is in the starting system. S5.2.3 Key removal override option. At the option of the manufacturer, the key may be removed from the starting system without the transmission or gear selection control in the ``park'' position under one of the following conditions: (a) In the event of electrical failure, including battery discharge, the vehicle may permit key removal from the starting system without the transmission or gear selection control locked in the ``park'' position; or (b) Provided that steering or self-mobility is prevented, the vehicle may have a device by which the user can remove the key from the starting system without the transmission or gear selection control locked in ``park.'' This device must require: (i) The use of a tool, and (ii) Simultaneous activation of the device and removal of the key; or (c) Provided that steering or self-mobility is prevented, the vehicle may have a device by which the user can remove the key from the starting system without the transmission or gear selection control locked in ``park.'' This device must be covered by an opaque surface which, when installed: (i) Prevents sight of and use of the device, and (ii) Can be removed only by using a screwdriver or other tool. S5.2.4 Gear selection control override option. The vehicle may have a device by which the user can move the gear selection control from ``park'' after the key has been removed from the starting system. This device must be operable by one of the three options below: (a) By use of the key; or (b) By a means other than the key, provided steering or forward self-mobility is prevented when the key is removed from the starting system. Such a means must require: (i) The use of a tool, and (ii) Simultaneous activation of this means and movement of the gear selection control from ``park;'' or (c) By a means other than the key, provided steering or forward self-mobility is prevented when the key is removed from the starting system. This device must be covered by an opaque surface which, when installed: (i) Prevents sight of and use of the device, and (ii) Can be removed only by using a screwdriver or other tool. [[Page 381]] S5.2.5 When tested in accordance with S6.2.2, each vehicle must not move more than 150 mm on a 10 percent grade when the gear selection control is locked in ``park.'' S6. Compliance test procedure for vehicles with transmissions with a ``park'' position. S6.1 Test conditions. S6.1.1 The vehicle shall be tested at curb weight plus 91 kg (including the driver). S6.1.2 Except where specified otherwise, the test surface shall be level. S6.2 Test procedure. S6.2.1 (a) Activate the starting system using the key. (b) Move the gear selection control to any gear selection position or any other position where it will remain without assistance, including a position between any detent positions, except for the ``park'' position. (c) Attempt to remove the key in each gear selection position. S6.2.2 (a) Drive the vehicle forward up a 10 percent grade and stop it with the service brakes. (b) Apply the parking brake (if present). (c) Move the gear selection control to ``park.'' (d) Note the vehicle position. (e) Release the parking brake. Release the service brakes. (f) Remove the key. (g) Verify that the gear selection control or transmission is locked in ``park.'' (h) Verify that the vehicle, at rest, has moved no more than 150 mm from the position noted prior to release of the brakes. S6.2.3 (a) Drive the vehicle forward down a 10 percent grade and stop it with the service brakes. (b) Apply the parking brake (if present). (c) Move the gear selection control to ``park.'' (d) Note the vehicle position. (e) Release the parking brake. Release the service brakes. (f) Remove the key. (g) Verify that the gear selection control or transmission is locked in ``park.'' (h) Verify that the vehicle, at rest, has moved no more than 150 mm from the position noted prior to release of the brakes. [71 FR 17755, Apr. 7, 2006]